SITE OF NICHOLAS RUSIN -

- PAINTING, SCULPTURE, PROSE AND MORE WHAT THAT


MAIN


LEAVE YOUR COMMENTS
ON THE PAGE OF OUR FORUM

Rare-OLD CARS

MOSKVICH-412

Сайт для инженеров и механиков

TROUBLESHOOTING Instrumentation and remedies

-------------------------------------------------- ------------------------------ Cause of Failure Solution -------------------------------------------------- ------------------------------ not counting work sites and high-speed speedometer The weakening of tightening the screws that connect the speedometer flexible shaft and speedometer drive ........................ Check and tighten nuts Jamming Mechanism .............. Replace speedometer speedometer Loss of a flexible shaft cable ................... Replace the cable or flexible shaft. Before Cars Gallery installation on a new flexible shaft, make sure that the reason for termination the cable was not sticking to the speedometer. To do so, attach the end of the flexible shaft to the speedometer slowly turn the pukoy free end of the cable. At the same time should not feel any jamming, and the speedometer needle should not depart from the zero division. If the axis of the speedometer does not rotate, replace the device Incorrect speed readings Violation of speed control unit Replace the speedometer ........ Uneven work (vibration) speedometer when driving at a constant speed Violation of speed control unit Replace the speedometer ........ Deformation or uneven effort scrolling flexible shaft ................. Replace ......................................... flexible shaft, neatly paved it, ensuring a smooth transition to a radius of not less than 150 mm Insufficient amount of grease inside the shell flexible shaft ............................. add lubricant. To add lubricant to the flexible shaft disconnect the cable from the shell flexible shaft, opening his first shut-off slotted washer and rinse carefully the cable sheath and in kerosene. Dry the rope and shell, and Lubricate cable along the length of a thin layer of grease TSIA-TEAM-201, GOST 9433-80, grease GOI-54, GOST 3276-89. Fill the shell at two thirds the length (the drive) the same lubricant dispenser with pressure 5.4 kgf / cm. Then insert the cable into the shell, put a washer and locking Crimp the ends on the cable When the ignition of oil pressure indicator shows zero although there is pressure Violation of a xcontact point where the sensor wires to the terminal ............. ...................................... Tighten screw wire sensor to the terminal Broken wire in the winding termobimetallicheskoy plate detector ................. Replace the sensor ...................................... With the ignition of oil pressure indicator shows a large pressure, although the actual oil pressure is low The closure of the winding plate termobimetallicheskoy sensor termobimetallicheskuyu plate due to violation of winding insulation ................................ Replace the sensor ...................................... The closure of the wires connecting the transmitter to the receiver, the weight ................. Remove the circuit ...................................... oil pressure indicator shows the pressure that does not match actual Violation of the sensor or control failure detector ..................... ...................................... Replace sensor or receiver With the ignition fuel gauge shows full tank, Although the tank is filled with some Weak xcontact between the sensor and a resxistor with a brush because of the weakening hold- contamination or oxidation of the wire resxistor ................................. ...................................... Preload brush or replace the sensor Break wire resxistor at the junction with the xcontact screw ............ Replace the sensor ...................................... Lack of xcontact with the ground wire connection pin screw gauge screw and pin receiver ......... Tighten nuts wires Lack of xcontact between the body and weight benzoreostatom .................. Provide a reliable xcontact ...................................... With the ignition shooter remains at zero, although the tank is partially filled Short circuit to ground screw or pin end of the wire resxistor connected to this screw .............. Replace the sensor A short to ground wire connected to pin screw receiver ........ Replace the sensor ........................................ Faults ................. Replace pointer pointer fuel gauge readings differ from the actual amount of fuel in the tank Violation of the sensor or control failure detector ..................... Replace sensor or ........................................ trick in store With the ignition the temperature gauge Cooling fluid remains in place Violation of a xcontact point where the sensor wires to the terminal ............. ...................................... Tighten screw wire sensor to the terminal Short-circuiting the sensor or receiver ...................................... ...................................... Replace sensor or receiver
©2010-2017 Сайт Николая Русина.