SITE OF NICHOLAS RUSIN -

- PAINTING, SCULPTURE, PROSE AND MORE WHAT THAT


MAIN


LEAVE YOUR COMMENTS
ON THE PAGE OF OUR FORUM

Rare-OLD CARS

MOSKVICH-412

Сайт для инженеров и механиков

CLUTCH. TROUBLESHOOTING THE MECHANISM OF ADHESION AND DRIVE and remedies

REASON FOR FAILURE Solution -------------------------------------------------- ---------- Stalled CLUTCH A. The complete absence of free movement of the clutch (no gap between the reference and the fifth clutch bearing) ................ Adjust the free play ........................................... the outer end of the clutch fork. If a strong deterioration Replace the release bearing. Two. Lubrication flywheel, pressure plate and clutch disc lining, or heavy wear linings ................................... Remove from the vehicle ................................... clutch rinse thoroughly with white spirit flywheel, pressure plate and clutch disc, Wipe dry with them. Remove the cause of grease. Strongly oily or worn, replace the clutch disc or rivet new friction linings. Three. Reduction of the working force grip ............................... Replace ................................ housing with a pressure plate collection. 4. Incomplete inclusion of coupling due to excess fluid in the system a hydraulic master cylinder due to clogging of compensatory holes or overlap its internal sealing collar ........ .................................................. ... ................................... Remove the filler cap reservoir master cylinder, remove the foil and soft wire - 0.6mm Clean the hole with compensation (see Fig. 67). If the hole overlap cuff, remove the master cylinder, disassemble it, and rinse all parts with fresh brake fluid or alcohol. After assembly, make sure that the piston is returned back to the vigor stop the puck, and wear a hole is not blocked cuff. If you wear a hole again overlaps the cuff, disassemble cylinder and replace the inner cuff. Allowed to gently (acute cutting tool) to cut the cuff until normal height. When swelling sealing cuff (due to the application Brake fluid is not recommended appropriate, either because xcontact with liquid gasoline, kerosene or mineral oil), drain brake fluid, brake fluid flush with fresh whole system hydraulic drive, replace the damaged rubber parts. After filling the recommended brake fluid prokachayto system. Five. Jamming of the working cylinder piston as it moves ................ Flush hydraulic system ................................. fresh brake fluid. Damaged parts or cylinder assembly replace the complete system of the recommended brake fluid. INCOMPLETE CLUTCH (CLUTCH "LEADS") A. Inappropriate increase in free running end of the outer fork Clutch ................................................ ................................. Adjust the normal free course of the outer end of the clutch fork. Two. Improper installation, a weakening or breakdown of rivets linings clutch disc ................................. Replace friction pads ................................. new, follow the correct riveting rivets in order to avoid damage pressure plate and flywheel. Three. Warping of the slave drive (complete with friction pads) ... ................................. Remove the clutch mechanism, remove the slave drive, if possible straighten it (mechanical runout allowed to 0.6 mm) or replace with new. 4. Bullies on the working surfaces of the flywheel or pressure plate ...... ................................. Remove the clutch and flywheel from the engine, proshlifuyte working surface of the flywheel and flywheel zpmenite new. When badass work surface pressure plate Replace the clutch cover pressure plate with a new assembly. Five. Sticking clutch disc hub on the primary shaft splines Transmission ................................................. ............ ................................. Replace the clutch disc. At significant deterioration or collapse the input shaft splines - replace shaft. Before assembling the slots should be lightly lubricated with grease LSZ-15. 6. Complete the clutch pedal is less than the required .................. ................................. Adjust the full pedal traction. 7. The presence of air in the hydraulic drive system ........................... ................................. Bleed the system according to their the instructions below. Eight. Leakage of fluid from the system .............................. ................................. Top up the fluid in the main tank clutch cylinder, bringing the liquid level to normal, and, when pressed all the way to the floor pedals, check the tightness of the pipeline, it compounds, and the working cylinder. In the event of leakage Tighten connections to eliminate leaks, replace the defective parts. Bleed the hydraulic system. In case of violation gemetichnosti master or slave cylinder disassemble cylinders rinse all parts with fresh brake fluid and if there is no damage to the cylinder or rubber sleeves, re-assemble the cylinder and check for leaks. If necessary, replace defective parts or cylinders in the collection. Bleed the system hydraulic drive. 9. Sticking front bearing shaft gear .... .................................. Replace the bearing. 10. Clogged holes in the lid of the tank, causing the vacuum in the main cylinder from which air is sucked into the cylinder through Seal ................................................. .. .................................. Clean the cover and clean the hole, bleed hydraulic system. Jerking when driving, when setting off IN SPITE OF SMOOTH clutch A. The loss of elasticity of the spring plates slave drive ................ .................................. Replace the clutch disc assembly. Two. Lubrication of working surfaces of friction linings slave disc, flywheel and pressure plate .................................. .................................. Rinse with white spirit flywheel and the pressure plate. Replace friction pads or slave drive in collection. Remove the cause of ingress of lubricant. Three. Pollution or non-technical conditions of the brake fluid, causing piston scuffing the cylinder when it is working Traffic ................................................. ........... .................................. Flush the entire system of hydraulic alcohol or fresh brake fluid. Damaged O- cuff or replace the cylinder assembly and refill system recommended brake fluid. 4. Damage to or loosening of pillows engine softening of the rubber suspension parts ............................. .................................. Remove damaged or weakened, replace the rubber parts engine mount. Five. Wear of front bearing shaft gear ...... .................................. Replace the bearing. 6. The deformation of the slave drive ....................................... .................................. Check out the deformation of the slave drive, straighten or replace a new one. 7. Bias the pressure plate deformation due to the housing with the wrong installing clutch on the flywheel ........................... .................................. Replace new pressure plate with the housing assembly. Eight. Looseness clutch disc linings Due to leaks riveting ................................................. .................................. If the pads are not worn, replace the defective rivets, if worn, replace them with new pads, watching the performance accuracy rasklepki rivets. Wrenches and Stroke TRANSMISSION IN CAR when starting ON LOCATION IN SPITE OF SMOOTH clutch A. Depreciation under the windows of the spring torsional vibration damper in the slave drive hub and the damper plate ................................. .................................. Replace the clutch disc assembly. Two. Much deposit or failure of the torsional spring damper fluctuations ................................................. .......... ................................. Replace the clutch disc assembly. Three. Bullies on the working surfaces of the flywheel, pressure plate, or linings clutch disc ................................. ................................. Proshlifuyte work surface flywheel, clutch disc lining, replace (or the clutch disc assembly). Replace the cover with the clutch pressure plate assembly. 4. Pollution or non-technical conditions of the brake fluid, causing piston scuffing the cylinder when it is working Traffic ................................................. .......... ................................. Flush the hydraulic system alcohol or fresh brake fluid. Damaged O- cuff or replace the cylinder assembly and fill the system recommended brake fluid. Five. The deformation of the slave drive ........................................ ................................. Check out the deformation of the slave drive, straighten or replace a new one. 6. Excessive wear or cracks on the friction slope adkah slave drive ............................................... . .................................. Replace friction pads or the clutch disc assembly. Rattle, knock or noise with the clutch A. Wear of torsional vibration damper ..................... ................................... Replace the clutch disc assembly. Two. Depreciation under the windows of the spring torsional vibration damper in the slave drive hub and the damper plate ................................. ................................... Replace the clutch disc assembly. Three. Much deposit or failure pruzhingasitelya torsional fluctuations ................................................. ......... ................................... Replace the clutch disc assembly. 4. The gap or weakening of support rings compression spring tie fingers to grip the casing ........................................ ................................... Replace the pressure plate to the housing in the collection. Five. Loosening the supporting heel to push the spring .......... ................................... Replace the base plate. 6. Wear of xcontact surfaces ................................... ................................... Replace the base plate. 7. The deformation of the slave drive ....................................... ................................... Check out the deformation of the slave drive, straighten or replace the new Eight. Large clutch wear poshipnika ..................... ................................... Replace the bearing 9. Too much pedal when the clutch ........... ................................... Adjust the pedal 10. Large or uneven wear on the hub clutch disc splines or the input shaft gear ................................ ................................... Replace the clutch disc assembly, and, if necessary, the input shaft gear. 11. Wear of front bearing shaft gear ..... ................................... Replace the bearing REPEATED FAILURE spring plates Clutch disc The deformation of the clutch housing (eg, due to the impact on road pripyatstvie), causing a misalignment of holes in the crankcase under the rear bearing shaft and the flange of the crankshaft a front bearing shaft gear ............. ................................... Replace the clutch new Failure to return the clutch pedal in the starting position After being removed from her legs A. Breakdown or weakening of the snatch springs the clutch pedal ....... .................................. Replace the spring Two. Sticking to the pedal axis .......................................... .................................. Remove the jam INCREASE EFFORTS REQUIRED FOR CLUTCH Sticking to the hinged joints of the clutch or drive .................................. remove or replace the jamming worn parts.
©2010-2017 Сайт Николая Русина.