SITE OF NICHOLAS RUSIN -

- PAINTING, SCULPTURE, PROSE AND MORE WHAT THAT


MAIN


LEAVE YOUR COMMENTS
ON THE PAGE OF OUR FORUM

Rare-OLD CARS

MOSKVICH-412

Сайт для инженеров и механиков

TROUBLESHOOTING engine , and their methods .Chast one.

-------------------------------------------------- ------- starter does not work -------------------------------------------------- ------- Discharge the battery. Oxidation of the findings and not dense tightening lug wire ...................... .................................................. .......... ........ Check and recharge the battery. Clean, inspect and tighten the lug bolts. Replace the wires and ends, if they are overly worn. -------------------------------------------------- ------- engine does not start -------------------------------------------------- ---------- 1. Part planting or disconnecting the wires from the terminals ignition coil to the distributor, and from nnego to candles Ignition ................................................ Find ......... faults and fix them. Check restore or replace the wire connection. -------------------------------------------------- ------- 2. Faulty solenoid or pneumatic EPHH valve ............... Replace valves. -------------------------------------------------- ------- 3. Lubrication or incorrect electrode gap spark ..... .............. Clean and adjust spark gap between the electrodes. -------------------------------------------------- ------- 4. Improper installation of ignition ......................... Adjust the installation of ignition .............. -------------------------------------------------- ------- 5. Faulty ignition coil .......................... .............. Check and replace the coil ignition on the new -------------------------------------------------- ------- 6. Cracks in the Distributor Cap ............. Replace the cover .............. -------------------------------------------------- ------- 7. Cracks, burning or accumulation of moisture on the runner Ignition distributor ................................. .............. Strip and replace if necessary runner -------------------------------------------------- ------- 8. Damage or wear of the moving xcontact-breaker or easing the pressure spring ............................. .............. Replace the xcontact and the corresponding spring -------------------------------------------------- ------- 9. The breakdown of the capacitor ................................... .............. Check the capacitor on the stand, if necessary replace with new -------------------------------------------------- ------- 10. Improper fuel level in float chamber ....................... carburetor check and adjust desired level of fuel in the float chamber -------------------------------------------------- ------- 11. Clogging the carburetor or fuel line ............. ............... Disassemble and thoroughly clean the carburetor, if the problem persists, wash and blow out the fuel tank and fuel lines -------------------------------------------------- ------- engine does not develop full power -------------------------------------------------- ------- 1. Improper installation of ignition ......................... Adjust the installation of ignition ............... -------------------------------------------------- ------- 2. The use of low-octane fuel .................... ............... Use gasoline with the corresponding octane -------------------------------------------------- ------- 3. Insufficient compression .............................. ............... Check the compression compressometer -------------------------------------------------- ------- 4. The absence of gaps in the valves .......................... ............... Adjust valve clearances -------------------------------------------------- ------- 5. Burning or deformation of the valve ..................... ............... Replace defective valves. -------------------------------------------------- ------- 6. Get burned pistons .................................... ............... Replace the piston -------------------------------------------------- ------- 7. Breakage of piston rings or coking ............ ............... Replace the piston rings -------------------------------------------------- ------- 8. Excessive wear of piston rings and cylinder on the heat gap ......... Replace the piston rings, if necessary - pistons and cylinder liners -------------------------------------------------- ------- 9. Break of cylinder head gasket .................... ............... Replace the gasket -------------------------------------------------- ------- 10. Carburetor malfunction ............................ ............... Wrong level of fuel in the float Adjust the camera ......... fuel in the float chamber -------------------------------------------------- ------- 11. Carburetor malfunction ............................ ............... Faulty accelerator pump ...... ............... Check the accelerator pump and supply, if necessary, replace defective parts -------------------------------------------------- ------- 12. The composition of the mixture is too poor .......................... ............... Check calibration of jets -------------------------------------------------- ------- 13. Faulty ignition distributor ............... ............... Violation of regulation of the centrifugal regulator ignition .......................... ............... Adjust the valve on the stand -------------------------------------------------- ------- 14. xcontact wear thumb .............................. ............... Replace slider -------------------------------------------------- ------- 15. The weakening of the moving xcontact spring breaker ... ............... Replace the hammer complete with a spring -------------------------------------------------- ------- 16. Incomplete opening of the xcontact breaker ............. ............... Adjust the xcontact breaking -------------------------------------------------- ------- 17. Depreciation kulochka roller valve .................. .............. Check and replace the valve spindle -------------------------------------------------- ------- 18. Excessive run-out roller raspredeliitelya ............. ............... Check and replace distributor worn parts -------------------------------------------------- ------- 19. Fuel pump failure ...................... ............... Check the pump and replace worn parts -------------------------------------------------- ------- 20. Overheating engine ................................... ............... Check the coolant level in the expansion tank and radiator, fan belt tension and thermostat. Perform the desired repair. -------------------------------------------------- ------- 21. Depreciation cams camshaft ............... ............... Check the valve timing and compare them with the dixagrams of the phases, if necessary, replace the shaft. -------------------------------------------------- ------- 22. Attenuation valve springs .......................... ............... Disassemble the cylinder head, check the elasticity of the springs and, if necessary, replace. -------------------------------------------------- -------
©2010-2017 Сайт Николая Русина.